Pin allocation, user manual 4269.40100 V1.0 <--> Board

ptqfp144
New Member

Posts: 23

Pin allocation, user manual 4269.40100 V1.0 <--> Board Nov 27, 2016 11:37:08 GMT

Quote

Post by ptqfp144 on Nov 27, 2016 11:37:08 GMT

Hello,

Doing a first few tests with this great board I noticed differences between board and manual for :

J403 Communication --> manual has swapped pins 1...8 in 8...1.
J404 ADCL --> manual has swapped pins 1...8 in 8...1.
J405 ADCH --> manual has swapped pins 1...8 in 8...1.

For all connectors the silkscreen on the board looks to be right , so the changes have to be made in the manual.

Gr.
Sander

ptqfp144
New Member

Posts: 23

Pin allocation, user manual 4269.40100 V1.0 <--> Board Nov 27, 2016 13:01:27 GMT

Quote

Post by ptqfp144 on Nov 27, 2016 13:01:27 GMT

Hello ,

p.s. the documentation is actually correct ! but for me a bit confusing because the position of pin 1 is sometimes up and sometimes down.

For J403 , J404 and J405 it maybe more logical to position pin1 at the top of the connector , just as on the board.

This was done for the powerconnector.

Related to notation on page 25 , Connector Pin Allocation.

Gr.
Sander

ptqfp144 New Member Posts: 23	Pin allocation, user manual 4269.40100 V1.0 <--> Board Nov 27, 2016 14:55:40 GMT Quote Select Post Deselect Post Link to Post Back to Top Post by ptqfp144 on Nov 27, 2016 14:55:40 GMT Hello, Attached my little drawing for Pin location on the board. ShieldBuddy_TC275_board_v1c.pdf (35.79 KB) Gr. Sander

mjb Full Member Posts: 166	Pin allocation, user manual 4269.40100 V1.0 <--> Board Nov 28, 2016 9:25:30 GMT Quote Select Post Deselect Post Link to Post Back to Top Post by mjb on Nov 28, 2016 9:25:30 GMT Hi, Great drawing. What did you use to make it? If you can send the original file we will put it into the user manual!

ptqfp144
New Member

Posts: 23

Pin allocation, user manual 4269.40100 V1.0 <--> Board Nov 28, 2016 10:10:57 GMT

Quote

Post by ptqfp144 on Nov 28, 2016 10:10:57 GMT

Hello,

The drawing is made with Draftsight from 3DS , makers of SolidWorks and Catia.

Draftsight can be used free but you have to do registration.

It's actually the best 2D drawing tool I've seen for many, many years.
It's like autocad light but then without the costs.

www.3ds.com/products-services/draftsight-cad-software/

My drawing in :

ShieldBuddy_TC275_board_v1c_cleaned.dwg (173.99 KB) (with bitmaps of the board)

p.s. the .dxf file is to big to upload.

Last Edit: Nov 28, 2016 10:11:30 GMT by ptqfp144

Pin allocation, user manual 4269.40100 V1.0 <--> Board

Post by ptqfp144 on Nov 27, 2016 11:37:08 GMT

Post by ptqfp144 on Nov 27, 2016 13:01:27 GMT

Post by ptqfp144 on Nov 27, 2016 14:55:40 GMT

Post by mjb on Nov 28, 2016 9:25:30 GMT

Post by ptqfp144 on Nov 28, 2016 10:10:57 GMT